Parts & Accessories
Why have your CO2 cartridges rattling around in a seat bag when you can get Xlab's Sonic Nut Inflation Holder and store them behind your saddle? It holds two threaded CO2 cartridges and an inflator (each sold separately) in an easy-access location. The Sonic Nut is compatible with Xlab's Sonic and Turbo Wings.
Why have your CO2 cartridges rattling around in a seat bag when you can get Xlab's X-Nut Inflation Holder and store them behind your saddle? It holds two threaded CO2 cartridges and an inflator (each sold separately) in an easy-access location. The X-Nut is compatible with Xlab's Carbon and Super Wings.
- Solution for mounting pumps and C02 inflators on frames or seatpost - Soft rubber block and Velcro loops hold pumps tightly
Topeak's Presta Valve Extender is the perfect solution for getting to those hard-to-reach valve stems. It's precision-machined from aluminum and is designed to fit deep-dish carbon and aluminum rims that have a depth of 60 to 90mm. And, it comes with an O-ring seal to ensure a leak-free fit.
A metal valve tool designed to tighten or remove Schrader and two-piece Presta valve cores. A special tool feature can also tighten or loosen Presta valve extensions. - Material: Aluminum - Schrader or two-piece Presta valve cores - Weight: 7 grams - Size: 4.5 x 1.1 cm / 1.8“ x 0.4”
Pssstttt. Tired of hearing that when you disconnect your shock pump? Well, hear it no more thanks to Topeak's Pressure-Rite. It's a must have for suspension fanatics as its ingenious design prevents air loss when adjusting shock and fork pressure. It's also available in a Presta version, perfect for disc wheels.
A Schrader valve adapter allows using the JoeBlow Ace floor pump for quickly pumping forks and rear shocks. Built-in air release knob allows fine tuning air pressure.
Upgrades any pump to a SmartHead pump head. Includes hardware, 40-inch hose, and SmartHead pump head.
Topeak's SmartGauge D2 boasts a digital readout that goes up to 250 psi and it's compatible with Presta and Schrader valves, as well as shocks and suspension forks. The head rotates 180 degrees to get in tough spots, and an air release button helps you dial in the perfect pressure.
Easy-to-read digital gauge can be attached to a pump or used alone and provides accurate pressure readings up to 300psi / 20.7bar. Rotating head works with Presta, Schrader or Dunlop valves on bike / motorcycle / car tires, forks or shocks while the Thumb Lock lever ensures an airtight seal. The air release button allows fine tuning pressure. Specs - PUMP HEAD COMPATIBILITY: Presta / Schrader pumps - TIRE VALVE COMPATIBILITY: Presta / Schrader / Dunlop valves - GAUGE: Digital, 300 psi / 20.7 bar - UNIT: psi, bar, kg / cm2 - BATTERY: CR2032 x 1 (included) - THUMB LOCK: Aluminum - PRESSURE TUNING: Air release button - BODY: Aluminum / Engineering grade polymer - SIZE: 9.2 x 5.8 x 4.3 cm / 3.6” x 2.3” x 1.7” - WEIGHT: 102 g / 3.60 oz Added Features: - Rotatable head / gauge - Auto-off function
- Ball-inflating needle for footballs, basketballs and more
- Genuine Sunlite replacement hose - Type: Fits Sunlite Frame Pump : 5.25mm
- Genuine Sunlite replacement hose - Type: Fits Sunlite #4301 : 16 5.8mm
Don't guess at your tire pressure, know with Sunlite's Duo Sport Gauge. This precision gauge reads your pressure accurately to 160 psi. The dual head works and plays well with both Presta and Schrader valves, too.
The Iconic SILCA 24.1 gasket is the heart of the press-on Presta chuck. The current 242 gasket utilizes a high tech and very red, fully synthetic elastomer base material.
Replacement gasket for reversible brass chucks, modern Impero Frame Pumps, and Pocket Impero
This chuck comes from the same vendor who supplied them to SILCA pumps for more than 25 years. It makes a great replacement or addition if you are buying a new Stainless Presta chuck or CP1 Disc Adapter for your older pump. This part is made from nickel-plated brass and uses an o-ring to seal the connection. - Hose barb fits into all SILCA hoses both old and new - Threads onto Schrader valves and all SILCA chucks with male Schrader threads (17-4 Presta chuck, HIRO, and CP1 Disc Adapter) - All metal construction, nickel-plated brass
n partnership with the rubber and tire experts at Continental , we are offering a custom extruded 3/16" ID air hose compatible with all historic PISTA Handles.
Years ago while Josh was working with the Team CSC at the Dauphine Libere, he noticed one of their mechanics using the most amazing little chuck to manage the disc wheel inflation. Unlike anything he had seen before, it was all metal and used a 'lollipop' lever on the side to lock onto the valve stems in disc wheels. The mechanic explained that these were made in Japan and were coveted by all the Euro-Pro mechanics due to their scarcity. So Josh set out to improve the design and make it available to cyclists everywhere. - Full metal construction, guaranteed for 25 years and covered by SILCAShield - Can effectively seal on valve stems as short as 10mm! - Uses SILCA 254 High-Tech Elastomer gasket - Adjustable gasket pre-load allows for a custom fit on any valve as well as compensation for gasket wear - Male Schrader thread fits into any Schrader chuck, or use SILCA Thread-On Schrader Adapter to fit a bare hose - Bullet-proof high-pressure, disc-compatible chuck for high-pressure situations.
Head Washer for 2371 Head
Bag of 3 replacement washers for EVA heads on all SKS floor pumps
Easily adapts schrader only air compressors, floor pumps, and mini pumps to work with presta valves
The Airchecker from SKS is a fast and easy way to check your tire pressure. The swiveling head makes it a snap to reach your presta or schrader valve stem at any angle, and the backlit display with extra-large LED digits is always easy to read. This gauge measures up to 144 psi and reads in 10ths of psi.
Prestacycle redesigned the Presta Grommet in May 2012 to fit to modern standards. PRestacycle's design works so well, it’s been copied by others including major floor pump makers. Prestacycle's design engages the Presta valve just below the cap threads and requires less insertion. The head is now very easy to get on and off, and gives a nice “click” feeling when it’s installed in the right position. Safe for all types of Presta valves, including tubeless and tubeless-conversion valves. Will not harm newer lightweight performance valves. Fits all Prestaflator BIG Push/pull Presta heads. Also fits all Silca pump heads that use the 24.1 or 242 Gasket.
Renew all the seals in your Prestaflator tool. These o-rings fit the hose, Pressure Release button and Trigger Plunger on a Prestaflator tool. Kit also includes internal trigger-plunger washers for 2010 and newer Prestaflator tools. O-rings made from high quality buna-nitrile (BN70) rubber with a durometer rating of 70. Updated 2013 Plunger seal is more reliable and gives the tool easier trigger regulation and retro-fits to 2010 and newer tools. Presta Head washers and rebuild kits are now sold separately.
$4.95 - $5.95
Prestacycle's newest version of the Presta Head Gasket uses Urethane Elastomer. It’s softer and stronger. It lasts more than 5 times longer, gives a better seal and flexes to work anywhere along the Presta shaft for better tubeless tire application.
Allows you to reach into difficult places with your Prestaflator hose. Great for cleaning and drying parts on-or-off the bike. If the tip is blocked, The safety feature releases air away from your work so you can maintain control. Can also be used to inflate low pressure vinyl-valve items (beach-ball type). The safety release feature will help prevent over-inflation. Made with 6061-T6 Alloy – it’s as strong as Brass and only 1/3 the weight. Note: The safety feature is only functional when the tip is used on a Prestaflator.
Prestacycle's new Mini Angle Presta Head has more room to fit into more wheels. It includes their newest version of the Mini Presta Head Gasket using Urethane Elastomer. It’s softer and stronger. It lasts more than 5 times longer, gives a better seal and flexes to work anywhere along the Presta shaft for better tubeless tire application.
Smaller Head fits every known Disc wheel made. Includes Prestacycle's newest version of the Mini Presta Head Gasket uses Urethane Elastomer. It’s softer and stronger. It lasts more than 5 times longer, gives a better seal and flexes to work anywhere along the Presta shaft for better tubeless tire application.
It’s back, the Pro’s favorite! Perfect for Tubeless tires, valve extenders and any Presta valve. It includes Prestacycle's newest version of the Mini Presta Head Gasket using Urethane Elastomer. It’s softer and stronger. It lasts more than 5 times longer, gives a better seal and flexes to work anywhere along the Presta shaft for any Presta application. Prestacycle's design engages the Presta valve just below the cap threads and requires less insertion. Deep head adapts to a wide variety of applications including valve extenders. The head is now very easy to get on and off. This head is a MUST for Tubeless tire users. Allows high-flow inflation with the valve core removed for seating tires. PUSH on / PUSH off – the fastest way to get you going. Made with nickel-plated 6061-T6 alloy – Strong as Brass and only 1/3 the weight. It’s also compatible with Silca pumps and can be adapted to other pump brands with our optional Schrader barb or our floor pump replacement hose. Patent-pending 2-way connector screws onto the Prestaflator threaded connector or directly clamps to a hose.
Page 1 of 3 Next page